wmclarenf1

LOL.. Somehow I don't think DWD will pay Costner 200 mil even if they had the dough... What's happened to him anyways... He's still around I hope.

They can;t as Kevin Costner endorses Cally :-)

Thanks T. REally funky looking stuff!

I knew they make snazzy bags, head covers, apparel etc but wedges? Who forges their heads? In Japan and this guy that grinds them used to be with Fourteen or some other brand? Any one played these? Any good or just snazzy bilngy looking wedges?

All metals do have a breaking point but I think anything 3 and less is not and issue for good forgings but I have personally bent closer to 5 degrees without issue.

Hi, I won't have that problem because i only use 3W off the tee on tight par 4s. It's shot for shot the most expensive club in my bag LOL.

Got a D1 F3 on the way in. Could put a similar Quadra 55 SR shaft in her to give it a good side by side compare with the Egg Spoon!

The lie angles are right for you I trust. Have a great trip to Maui!

You bother with the tees? I'm just looking for the naked ladies :-)

I'll spine the new TJ46 I have coming in from you and see how that goes.

Sorry friend but I'm really out of touch with scotties.

What length were you playing it at? Could it be that you played it longer than the 43 prescribed by Ryoma? Thanks for the feedback.

Quadra told me either log up or down but I can tell you like what RI says, the spine is not always logo up or down. Close to it but not always. I'm not referring to the different philosophies of how and where to put the spine as there are differing views one which T mentioned which I believe is to prevent toe droop. but where the spine is actually located .

Don't need this anymore. Thanks for looking.

The Roddio shafts were great but sensitive to spinning I found and it was not as simple as putting the silver half facing up or down. I am finding out now that Crazy and Quadra despite what they (or rather Quadra may say) are spine sensitive as well even with the higher bass, modulus carbon stuff.

i, Can you elaborate on what about the F3 you did not like? As for your comment on the Ryoma driver, I can;t agree more. If forced to go with just one driver, my D1 TJ-46 is it!

I've played them in the Epon ProIs and now the Romaro Hs and no ballooning. In fact, hitting my irons as log as I was and then some as when I was younger and pre-accident. Anyways, probably swing related and no right or wrong.

I have played NS Pro 750s for a long while and have played 950s and before that PXs. You can hit them low if you need to. I can tell you that the NS Pros on their own do not balloon despite being a low kick shaft. Haven't played the aerotechs so I can;t comment on them. What heads did you play the NS Pros in?

Do I get a RomaRo cart bag, headcovers, cap, belt etc for helping promote them LOL...

This must be one of the best priced Crazy shafts I have seen. GLWS bump.

Well, with some biasness, I would say if you want to try JDM, try the GS... not the softest feeling but whatever mill is on these really makes puts on a great roll.

Sorry man... just the H's because the design and look of it appealed to me first just like the 460HX which is anoter RomaRo club you should try :-).

PLayed 18 this morning. OK, the H irons are firmly in the bag now. I'm not a great shot maker at 10 handicap but when I did attempt fades, draws and keeping the ball down today (it was really windy on the back 9), it was a lot easier to do than with the Pro Is. Again, same shaft, setup, ball and hacker. If you guys are looking for a new set of irons, do try give the H irons a go!

hehehe.. did you get the one on ebay last night?

Selling some of these older Epon and Miura wedges as heads only. All heads are non-conforming but if you don;t care about that and just want some good old fashion and soft wedges, these are it. I'm not sure whether the Miura is conforming or not and have asked T to help ascertain but for the sake of this post, assume it is NON-conforming. 1. Epon COPPER X Wedge 52-06. I am comfortable to bend this 2* either way if you choose. 2. Epon Technity 60. Can;t remember the bounce but it is low. I think maybe 7 or less. This head is meant and will rust. I am comfortable to bend this 2* either way if you choose. 3. Miura Giken WMF-01 PW. It is 46* now but I can bend it to 47 or 48 is you choose. Asking $75 per HEAD ONLY PLUS shipping which I think wil be about US$20-$25 so lets just say all in per head shipped by post with track and paypaled is $95 per head. Not fussed if these don;t move as these will make cool paper weights for the study but these are great heads and play really well so I thought someone may want a deal. Thanks for looking.