Everything posted by Duffer19
-
Epon Personal 3 Irons Revealed - And it's not a blade!
Its more like a limited model between the 551 and 703 than a replacement for P1/2. Did Epon designate this model as P3?
-
Epon Personal 3 Irons Revealed - And it's not a blade!
Haven't look at their website yet but somehow this doesn't look like a replacement for P1 or 2 but more like 503/703. If that's the case, this would make more sense.
-
Itobori Driver!
I only have one question, WHY?
-
Areso E13 by Rock Wu
Who the hell is Rock Wu?
-
Miura Giken's New HAYATE Driver
Yes it's made in Taiwan as stated on website. by Dynamic ?
-
Will a UT shaft work on a FW?
Never try it but 5W would be 0.335 hosel width and UT would probably be 0.355 tip dia. You would have to shave the Crazy ut tip to fit. Unless it is dirt cheap, just don't understand the logic of doing it.
-
Epon AF-205 & Tour Wedge
C, is Epon still making any wedges in copper?
- EPON AF-105?
- EPON AF-105?
-
Help please! Looking for a set of high end graphite shafts with .355 taper
Since most the shafts mentioned are 0.370 which needs to be sanded down to fit, you might as well consider the Bangvoo that your already own. It would be the same exercise of sanding it down. My fitter sanded down the MCI to fit my AF703 and OT85 to fit my RF551 without any issue.
-
SOLD
I have the same set with Roddio I-6 but couldn't get a reasonable offer so also decided to keep it. Unfortunately this is the market now but the 551 is really a keeper.
-
who makes hybrids in 30/34 and above lofts?
Carlo. Ena might have these kind off loft since whole line is designed for senior and super seniors.
-
7D Divot Tool & Coaster Pics
That's USD3 each give or take a dollar.
-
New OT75 and OT105 Shafts Coming by Mitsubishi
Do not install them straight in. Follow the tipping guide and it you want to soft step or hard step, take 1/2" less or more to achieve stepping. The shafts all come in one length so just butt trimming to lenght wouldnt work and you would ruin the set. For those not sure about flex, you can order just one or two shafts to try instead of whole set.
-
Face Progression Vs Offset, Same Thing?
Face progression and offset are exactly referring to the samething but using different method of measurement. Do a search here for Tario's very detail post or blog on the subject. The value is exactly opposite in meaning, l.e. The higher value in FP, the less offset of the club if I remener correctly.
-
Want to Buy Epon AF-703 Irons
Hope you did not get it from A+.
-
Ryoma Betond Power - No Groves?
The driver face has been shaved and I believe the seller stated that it is now non conforming.
-
Ryoma Betond Power - No Groves?
Thats funny, the beyond power driver is the same Maxima head for the past few years and only shaft is the difference. Both my two Maxima have 'groves'. Perhaps you should attach the picture you have seen.
-
Ferrule for Egg Driver Shaft?
I think I have seem those on Geotech site and on another online shop.
-
Rare Epon RF551 5-PW with Roddio I-6
Already promised the shafts to another member pending my return to HK. If it doesn't happen, I would post the, on BST again.
-
Rare Epon RF551 5-PW with Roddio I-6
Firstly Free, it's not your old set since I got them new. Secondly it's off the market now since I am shafting them with OT85 for the fun of it since the set was on the market for awhile and not taker.
-
.355 Graphite Iron shafts
PM sent
-
Softest stickiest grips???
No. 1 was my number 1 and still one of the best but I am now using Masda slick for a change. The Masda is very soft also.
-
Epon AF 301.
Gone full circle again? You sold the 551 to my buddy and now you want another set? My set was on the market for quite awhile but now I think I would keep it as cannot find anything good to replace them.
-
RYOMA MAXIMA 10.5
Well in that case, you're not getting mine.